LockDownRadioControl

A free, open-source radio control system you can build yourself

Model options

The help for this page of the Version 2 transmitter, as its latest update shows it. On the transmitter, Animation at the top of this help page plays a short film of the page in use.

On the transmitter: Model setupOptions

This model's trims, motor switch, timer and warnings.
Touch a box to type a new value.
Touch a switch to turn it on or off.
'OK' keeps the changes and goes to the Front screen.

Model options: trim multiplier, throttle channel, motor off in microseconds (usually 833), the timer, battery and current warnings, the model's picture, and the switch Six banks (off: four)
The page as the transmitter shows it. Tap to enlarge.

Trims

Trim multiplier (0 = off): how far each trim step moves.
5 is a very good default. Use 0 on a flybarless helicopter.
Copy trims to all banks: on, a trim change goes to every bank.
Off, each bank keeps its own trims.

Motor

Throttle channel: the channel the motor (ESC) is on. Usually 3.
Motor off value: what the throttle channel is sent, in microseconds, while the motor is off or the safety is on.
833 is the default, and nearly always right (it was -67 in the old units). 500 is the lowest, 2500 the highest.
It is not reversed with the channel:
if you reverse the throttle, change this value to match.

Use motor kill switch: on, the transmitter checks the motor switch before it connects: at switch-on, or after a lost link.
While the motor is on, it says 'The motor switch is ON.'
and waits until you switch it off and press 'OK'.
Not after a restart in flight (back within 30 seconds).
The motor switch has the job 'Bank 4 & Motor' ('Transmitter setup', 'Switches'). Its three positions:
Away = bank 1, 2 or 3, motor on.
Mid = bank 4, motor on.
Near = bank 4, motor OFF.
With 'Six banks' on, mid and near pick bank 4, 5 or 6 by the 'Banks 1 2 3' switch.

Six banks

On, this model has six banks (flight modes), as Rotorflight has six. Banks 5 and 6 start as copies of bank 4, with names of their own on 'Bank names', and their own trims, curves, expo and servo speeds. Reach them with the 'Bank 4 & Motor' switch at mid or near: the 'Banks 1 2 3' switch then picks 4, 5 or 6. Off, the four banks as before; banks 5 and 6 are kept on the card, and come back if it is turned on again.

For Rotorflight to follow banks 5 and 6, the bank line's channel needs a height of its own in each bank (its curve, on 'Model setup'), and the bank selector six positions: see 'Switches & knobs ...' on the Rotorflight menu (in the phone app:
'In-flight adjustments' and 'Switches').

The receiver and the phone app follow this switch: whenever the transmitter and the receiver connect, the transmitter says how many banks the model has; the app's pages show that many, and its bank selector is set to match. If the flight controller's bank selector has another number of positions, the transmitter says so on the Rotorflight menu, and so does the app: with the USB cable, open the switches page and Save the bank line.

Timer

The timer runs while the motor is on, and pauses when it is off.
Timer counts down: on, the timer counts down from 'Count down from (minutes)' and says the last ten seconds.
With 'Timer voice' on ('Transmitter setup', 'Sounds etc.'), it then says 'Stop flying!'.
Off, it counts up, and the minutes box is grey.

Warnings

Stop flying volts (per cell): below this, per cell, the transmitter says 'Stop flying!'.
It watches the model's battery, as the receiver measures it.
When the motor stops, the voltage recovers a little.
So set this a little lower than you might think.
Find the best value by trying: every model differs.

Volts correction (x 0.01 V): corrects a small error in that battery reading, in hundredths of a volt per cell.
For example, 5 adds 0.05 V to each cell. It may be negative.
Compare with a good voltmeter, and adjust until the two agree.

Current warning (A, 0 = off): above this current, the transmitter sounds a warning and shows 'Current too high!'.
It warns once each time the model connects. 0 turns it off.

More

'Model picture ...', or a touch on the picture, chooses this model's picture.
'Servo types ...': each servo's pulse rate and centre, for a Version 1 receiver.

The receiver's output (SBUS, CRSF, PPM ...) is not set here.
A Version 1 receiver always sends SBUS (all 16 channels) as well as its servo outputs.
On a Version 2 receiver, choose it on the phone app's 'Output protocol' page.

Still stuck?

See common questions, or write to mmessiter@gmail.com. Say which page, and what the screen showed.

↑